WxFisch

Even if they were, this isn’t what any of these people are trained for. Federal agents are not local police. They don’t go out on patrol or randomly deal with stressful situations. TV makes it seem like federal agents are out chasing bad guys every day but they spend a huge amount of time following leads, interviewing people, and digging up information from various sources (of which i make no comments on the legality of). None of these people are trained to be beat cops on the front lines every day this way.

It wasn’t standard previously, and if you have TV service I think it’s still inconsistent but the past ~5 years it seems to be more common that they are setup that way from the start. If you have internet only service, and a newer ONT (like less than 10 years old) it is the standard configuration and is how the self install guide tell you to hook up the “quantum gateway” router from Verizon.

You can always call and ask to have your ONT converted to Ethernet output if it isn’t already and as long as it supports it I haven’t heard reports of much trouble there. The very early ONTs though don’t support it though IIRC but those should be being replaced at this point anyways.

I mean you can, an ONT is not a router, it’s essentially a media converter. I use my own router (and have for many years) and had no issues. The FiOS tech even ran a long Ethernet run in my basement to connect the ONT and my router in my rack when they installed service.

It depends, and without knowing your ISP I’m not sure there is a way to tell you for sure. I know for example Comcast gigabit Pro has been known to directly connect to an ISP SPF module in your firewall/router, but Verizon FiOS (and most FTTP that I know of) provide an ONT that converts the fiber to Ethernet which you would then connect directly to your hardware.

I would verify if the ISP router you refer to is not really an ONT in which case you are directly connected to the ISP functionally and there isn’t really an advantage to getting an SPF and getting the fiber directly connected if you even can.

I feel this way sometimes, then remember what the alternative was and don’t feel as bad. (To save the lookup for those that don’t know, Mehmet Oz was the republican candidate in 2022).

I’m curious how everyone documents their core/critical configs to allow the non-technical in our homes work with it if needed. For instance if I’m on work travel and the Pi-hole goes down for whatever reason my wife wouldn’t be able to use pretty much anything online. I can remote in and fix it but that could be hours/a day or two later. Same then for the proxmox stack that everything runs on.

Along the same lines, how are folks documenting for EOL? It may not be a happy thought but we are all going to go someday, so what is your plan and how have you ensured loved ones can access/save important data?

Agree 100%. Most of the former Plex users turned Jellyfin users I have come across did so better Plex was broken in some way for them. For me it was the general lack of care in creating/maintaining a good Apple TV app. Over the past few years it’s just gotten buggier and buggier with a lot of complaints on the Plex forums where devs would essentially stop by to say they weren’t working on any fixes.

Jellyfin doesn’t fix 100% of the issues, but at least there is active development on Swiftfin that showed a desire to fully support all devices.

So paperless works as a service that ties into your storage. I point mine at an NFS share on my Synology and just backup that share. The documents are all stored as PDFs still so worst case I still have “dumb” copies without all the tagging available if my paperless instance goes offline for some reason.

I use Backblaze B2 through my Synology NAS to offsite my important data. Most things though I just backup locally and accept the risk of needing to rebuild certain things (like most of my movie/TV media files since I can just re-rip my physical media, and the storage costs are not worth the couple of days of time in that unlikely case).

I really think this is key when thinking about your backup strategy that is specific to self hosting compared to enterprise operations. The costs come out of our pockets with no revenue to back it up. Managing backups for self hosting IMO is just as much about understanding your risk appetite and then choosing a strategy to match that. For example I keep just single copy in B2, since the failure mode I’m looking to protect against is catastrophic failure of my NAS which holds my main backups and media. I then use Proton Drive and OneDrive to backup secrets for my 2FA setups and encryption for my B2 bucket. This isn’t how I would do it at work (we have a fair more robust, but much more expensive setup). But my costs for B2 are around $15/mo which I am fine with. When I tried keeping multiple copies it had grown to over $50/mo before I cared enough to really rethink things (the cost of the hobby I told myself).

I misunderstood what you were saying, I wasn’t sure if protect required a UniFi hardware console or could be self hosted like the network application can be. It looks like it does require at least a Cloudkey gen 2 (or the plus which is what they currently sell) or one of their integrated consoles like a UDM.

It’s supported natively in the UI to configure: https://help.ui.com/hc/en-us/articles/26301104828439-Third-Party-Cameras-in-UniFi-Protect

It was added in EA in mid September and should be GA now as far as I know.

I use UniFi Protect and record to my UDM, though you should be able to install it all on your own hardware if you’d prefer. Their cameras are pretty decent but a bit pricy in a lot of cases. Though they do support 3rd party cameras now.

I’ve also heard a lot of good things about frigate, but I’ve not really looked into it since I already have UniFi gear.

Add in the congress critters from both houses need to run their own campaigns at some point, in many cases they can’t afford to just kiss the ring. This is especially true in the house where seats are up for grabs “soon” and the voter base is relatively small. If you’re a Representative and won your seat on a small margin, you clearly don’t have a mandate and need to act more moderate. Some senate seats are in the same boat (McCormick in PA, assuming the recount still favors him, is in this boat; he’s run three times now and barely beat out Casey this time, it’s a fair bet he doesn’t have solid footing for his first term and can only toe the party line so far). The only thing we should all bet on is at the end of the day everyone in politics is going to lookout for themselves first. It’s going to be a shitshow for at least the next two years, probably the full four and maybe beyond.

Here’s a gifted version, I think it still asks you to login but it’s not paywalled

https://wapo.st/3zKhYRV

So the plan is to request an early ballot, then to take it to your polling place and assume the poll workers won’t follow the process and then you’ll take a picture of your early ballot to somehow own the libs? At least in PA the poll worker will just have you relinquish the unmarked early ballot and then you’ll vote as normal. If you don’t have your ballot then you vote a provisional ballot that is only counted once it’s confirmed your early ballot wasn’t returned. It’s not a hard thing and it’s well understood by poll workers on what to do.

I would recommend prowlarr instead of jackett for indexer management, and pihole as at least an additional blocking service but in reality it’s really all you need for use at home. I’d also strongly encourage use of a VPN on your *arr download services. I use a separate box to run Plex and then have my *arrs all running on their own VM inside if it to provide separation and allow be to more easily segregate the network traffic (as someone that doesn’t really know docker that well it “just works” for me. Also probably worth looking at how to store your media on an external target, it’s easy to quickly accumulate 10s of TBs of media and trying to store that all on the server locally is asking for trouble. Better to set everything up on a NAS to start.